Quartz Fiberglass Fabric for High Temperature and RF Applications

Category: knowledge

Release date: 2026-11-16

Summary:

The Quartz Fiberglass Fabric from Canyue is a Q-glass fabric in the company's fiberglass fabric family. The product page lists a long-term use temperature of up to 1050 degrees Celsius and a dielectric constant as low as 3.78. It also lists high temperature resistance, good dielectric properties, high strength and high modulus. The fabric is available as QW100 at 108 gsm with a 20 by 20 thread count, and QW200 at 200 gsm with a 10 by 10 thread count, in a plain or a twill weave.

What Q-Glass Is

Q-glass, or quartz glass fiber, is a special glass fiber with a very high silica content. It keeps its strength and its electrical properties at a temperature where an E-glass fabric would soften or lose performance. The page lists a dielectric constant of 3.78, which is lower than a standard E-glass, so the fabric is used in a high-frequency or a radome application where signal loss matters.

Weights and Weave

The QW100 is a 108 gsm fabric with a 20 by 20 thread count, and the QW200 is a 200 gsm fabric with a 10 by 10 thread count. Both are listed in a plain or a twill weave. A plain weave is stable and has a balanced strength, while a twill weave drapes better and is easier to form over a curved mold. The buyer should choose the weave for the shape of the part, not only for the weight.

Q-Glass vs E-Glass

An E-glass fabric is the standard reinforcement for a general composite. It is lower cost and widely available, but its dielectric constant and its temperature limit are lower than a Q-glass. A Q-glass is chosen when the electrical loss or the service temperature is the limiting factor, even though the material costs more.

The buyer should compare the full data: the dielectric constant, the loss tangent, the strength, the modulus and the temperature. A fabric that wins on one value can lose on another. The page does not list the loss tangent or the strength, so the data sheet should be requested for a design calculation.

High Temperature Use

The 1050 degree Celsius rating is a long-term use temperature, not a one-time peak. The buyer should confirm the actual service temperature and the time at temperature, because a fabric that is used near the limit needs the right finish and the right handling. A heat-cleaned or a sized fabric behaves differently in a composite.

Electrical Properties

The low dielectric constant is the reason Q-glass is used in an antenna, a radome or a high-frequency circuit. The buyer should ask for the dielectric loss tangent as well as the constant, because a low constant with a high loss still gives a poor signal. The page lists the constant but not the loss, so the data sheet should be requested.

Composite Processing

The fabric can be used with an epoxy, a phenolic, a silicone or a cyanate ester, depending on the process and the temperature. The buyer should confirm the sizing or the finish, because a finish that is designed for an epoxy may not wet out in a silicone. A heat-cleaned fabric is used where the finish would burn or interfere.

The lay-up should be checked on a sample panel. The fabric should wet out evenly, and the weave should not distort under the vacuum. A fabric that is too tightly woven can trap air, and a fabric that is too loose can shift during the lay-up.

Quality and Roll Form

The buyer should confirm the roll width, the roll length and the splice rule. A splice in the middle of a roll can stop a cutting table, so the supplier should state whether a splice is allowed. The fabric should be checked for a broken yarn, a stain and a width variation.

Storage and Safety

The fabric should be stored in a dry place, away from dust and direct sun. A roll that is stored on a damp floor can pick up moisture, which affects the composite. The buyer should keep the roll in its original bag and should handle it with gloves, because a glass fiber can irritate the skin.

Applications

The page lists high wave transmission, high temperature resistance and heat insulation. The fabric is used in a composite, a thermal barrier or an electrical insulation part. The buyer should state the resin, the process and the end use, because a fabric that is compatible with an epoxy may not be compatible with a phenolic or a silicone.

Ordering and Contact

To order Quartz Fiberglass Fabric, send the model, the weight, the weave, the width, the roll length, the finish and the quantity. Canyue can be reached by phone at +86-023-47630699. Send the technical requirement and the sample request with the inquiry, and the team will confirm the fabric, the roll and the delivery before a quotation is issued.

Keywords: Quartz Fiberglass Fabric for High Temperature and RF Applications

Related News

knowledge